pinestore8

How to Change a Subaru Spare Key If you have lost your Subaru car key, call a locksmith. Usually, they will cut new keys for you for less than the dealer. Subaru car keys are generally either intelligent “push-to-start” fob remote keys or plain metal keys. The Fob key comes with an embedded chip and requires reprogramming. Keyless Entry System A key fob lets you to lock or unlock your Subaru from a distance. You can even unlock the trunk or lift gate of your vehicle. These remotes use the keypad inside your car to connect to your vehicle's computer. Subaru models come with a lesser well-known feature called PIN Code Access. You can use a customized number sequence to open and start your vehicle. Check subaru key copy www.g28carkeys.co.uk to learn how to use this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza. If your keys stop working, there's a good possibility that the battery in the key fob is dead. The first thing to ensure is that the key fob has new batteries You can do this with a portable remote tester or a basic multimeter from your garage. The next step is to remove the circuit board for the transmitter from the key fob and then examine it. This will have one or two sets of eight-digit numbers, so jot down the first set so you will be able to remember it later. Once you've completed this, you can start programming the key fob at home. The procedure for programming varies depending on the model and year of your vehicle but it's generally simple enough to do yourself. Key Fobs Subaru's newest models feature key fobs which not only unlock doors, but also turn on lights, lock gas cap, and even start the car. This last feature is particularly helpful if you've ever arrived at the gas pump only to find that your car won't start because the battery in the key fob died. Whether your Subaru is new or older it's likely that the key fob can be replaced without difficulty. Remember that some of the more modern models, with their advanced technology, might require visiting a dealer. With a little effort and time, you can build your own key fob replacement. Begin by looking at the circuit board that controls the transmitter on your key fob (instructions to open the case should be provided in the owner's guide). It should have one or two sets of serial numbers each of which is 8 digits long. Write down the initial number series and keep it in a safe place to refer to later. After that, get in your driver's seat, and close all the doors. Turn the key 10 times to start your car, and then switch off. Press the lock button on your key fob and open the door to ensure that your doors are functioning properly. Close the door, and then take the key off. The car should sound again, signalling that the key fob has been programmed. Ignition System The battery in your key may be dead If your Subaru keys aren't working as they should. If you are aware of the issue, you can replace the battery in your key fob yourself. A replacement battery is cheap and fairly easy to find. If your key fob won't respond to your commands, it may be a problem with it. To obtain a spare key, you should go to a dealer. They can ensure that the key is an original Subaru key, which is covered under warranty, and that it is programmed to your vehicle. This is much safer and easier than buying an aftermarket key from a business on the internet. The dealer is also able to cut keys for you provided you provide your VIN number as well as proof of ownership. This information is used to identify the new key so that it is accepted by your immobilizer. This procedure is more complicated than simply cutting a key, and the dealership will usually charge a higher price for this service. Once the new key has been programmed, you can switch it with your working key. It takes just five seconds to insert the new key, so make sure to keep your working key close at fingertips. When the security light stops flashing and you're able to remove the new key and test it to confirm it's working properly. Battery Replacement One of the main features that makes Subaru fobs useful is their ability to switch on your car's power windows as well as sunroof with just a press of a button. However, the battery in your Subaru key fob isn't designed to last forever and will eventually require to be replaced. This short guide from Capitol Subaru will help you to replace the battery on your own. You'll have to find the small crevice that separates the front from the back of your keyfob. With a small flathead screwdriver, you can break this seam open to reveal a small compartment inside which is the battery. Insert the new battery and make sure it is facing correctly. Remove the old one. After you have put everything together and you are ready to use the new key fob to lock in, unlocking, and even starting your vehicle. You should always have a spare set of keys, particularly if yours is broken or lost. A new key can be purchased at your local auto dealership, or you can have one made by an locksmith. In either case, it's vital to get your key fob working correctly in the shortest time possible to allow you to drive safely!